Monday, 28 November 2011

A Braiding we shall go!

Now I don't have anything in particular against silicone hoses, in fact I think they are good alternative replacements to the existing hoses when needed. What I don't understand is their use as engine dress up items. It seems to me that no matter how tired, dirty, worn out looking peoples engine bays are, the first thing that most people want to do is fit a silicone breather pipe set to it, usually in some awful colour (it seems that the colour 'blue' is too common), like bright green, lurid purple or orange red! Of course it does not help that usually folks on a budget seem to get their pipes a few at a time, like buying a breather set and then the radiator set. This often leads to the 'almost but not quite' school of matching colours. As a further aside you seem to pay a premium for silicone pipes if they have the makers 'logo' inscribed in huge while letters, professing how sporty they are! Of course the real irony of the whole situation in designer pipework is that the most elusive of the colour spectrum appears to be good old honest plain 'black' pipes! (Not that black is a colour, depending on what arty types you know).

I myself (being of a certain age) still like braided hoses. These were all the rage once and an Escort XR3i would be instantly raised a level by having a bit of braiding chucked under the bonnet. Now for all of you who cry out 'old hat' at my reminiscence, I say to you 'retro is in!'

My only problem with braided hoses is that I have never purchased any before. Where do you get them from and what size etc! It is then that it really becomes clear why people like silicone hoses!

Having had a look around braided hose comes in various ways. There is the straight forward inner diameter that you require hose, that is already braided. or there is over braid. Over braid is a bit like a sock that fits over your existing pipework, you can push it together to open it up and feed your rubber pipe through and then pull it tight over the pipe, the braid does all the work then. I usually use tin snips to then cut and trim the braid itself.  
The pre-braided pipework is somewhat easier and just needs to be cut to length. This can be done most effectively by wrapping electrical insulating tape around the braid and sawing it with a fine toothed hacksaw.

Now the actual fitting of the finishers can be a pain, as they are push on but with a jubilee clip built in. This would be fine but they are somewhat a tight fitting push on and can catch the braiding pushing it back! I usually clean up the cut end with my trusty tin snips, wrap electrical tape tightly around the end and tease the finisher into place until I can give it a firm push!
Naturally the wire of the over braid is annoyingly sharp and can fray like crazy, so it is good to make sure that it is tight over your pipe before mucking about with trying to push the end cap on!

For the technically interested, hose and finishers are listed by their 'AN' numbers. For instance 16 mm ID hose and finishers would be AN12. Whereas fuel line is AN6.. Although to confuse things... AN6 seems to apply to 8 mm ID and 6 mm ID. So check what size hose you are getting!

It is a bit of a pain to find one seller that does all the parts you would need for this. Although I have found this supplier Torques UK to be the best.

Now as I have this rather wonderful turbo from HKS fitted to my runabout, my pipework is marginally different and the rocker cover top breather hose is somewhat rather longer than standard. Originally I was going to do away with the Nissan 'bent' pipe connected to another pipe for one great long pipe. This isn't really practical with over braiding though as the silicone flexy pipes that you can get are just too fat to braid properly. Therefore I decided 'what the hell' and am going to connect one braided pipe to another.

AN6 pipe and finisher.

As to how it looks on the car. Well it's looking promising... I don't have any photo's as yet (not finished) but will post 'this week' when I have done. Okay to be honest I needed a couple more connectors (which are on order).

Thursday, 24 November 2011

R33 Engine Damper - review

A very popular 'modification' or addition to the engine bay, seems to be 'Engine dampers' the idea of this is, simply it will stop your engine 'moving' about under hard driving conditions and improve the life of your engine mounts.
Also but probably of less importance to the the average user, it also provides some dress up for the engine bay!

As you can see, the kit consists of a couple of brackets, a damper and a couple of screws. The brackets come in what looks like a nickel plate finish and whereby the finish is acceptable, it isn't of the first order. However they are quite passable. There are two brackets, the larger fits to the left hand suspension turret top (requiring your Strut brace to fit over the top of it) and also to the earthing points next to the fuse/relay box. The smaller of the brackets replaces the engine lift/hoist point.
Fitting of the engine bracket is a little fiddly as access isn't easy for bolt removal. This is increased when fitting the new bracket due to the rib that runs down it's center. However it can be done.

The damper has two rough cast ends (which you may want to clean up before fitting) and an anodized body. Usually supplied in red or blue, my example was not well anodised and it seemed slightly patchy on colour. I masked up, primed and painted mine in body colour before fitting.

The screws are zinc plated items.

When fitting (as mentioned) the screws can be a bit of a pain to do, in fact I found the harder ones were the ones located by the fuse box. It could also be said that if I had not been so lazy as to not move the fuse box out of the way beforehand, this would have been a simpler task!

The actual fitting of the item is good and it slots straight in. The unit comes shipped with no instructions or blurb.

Does it work?
Well 'they' say that fitting this to your car you will:
Reduce engine vibration, increasing horsepower to the flywheel as torque reaction is minimised.
Give a smoother, more linear power delivery through the transmission and to the rear wheels.

I say that the above statements are probably big claims, although I'm open to try them out!

Wednesday, 16 November 2011

A catch up!

Well, it appears that one thing quicker than Ms Skyline is time. I can't believe that we are rapidly approaching the end of the year. Mind you 'time' itself in terms of a 24 hour day, is an abstract concept I suppose and with my main turbo pipes at the polishers it seems to be taking 'forever' to get them back!

So pockets empty of cash and the economic climate also empty of cheer. We can all amuse our selves of the fact that Christmas rapidly does approach!

So to the car.. It has not sat idly by lately (as if I could stop tinkering). After completing the paint work on the slam panel and whilst the car is laid up STILL waiting for the pipework. I have indulged myself with some other works cosmetically enhancing her already good looks.

With this in mind I took a deep breath and started to work on the front splitter. This will be it's third clean up in a year so far (will get to that). Although the last time it was sprayed it was a rush job of a not very high standard. This time around I was determined to take my time and get it right!

Will not bore you with the photo's, although the finish is to a very high standard. To protect it from the dreaded stone chips I plan to vinyl coat it. Not decided on quite how yet, or if it is a job for me, or for someone that actually knows what they are doing.

I also removed the front Spec 2 Grill. Even though previously I had made do and mended, I was not 100% happy with the actual finish. I decided to 'man up' and completely strip the layers of previous owners paint back to the plastic and do a 'real' job of it. I can confirm that I must be it's third owner as my black coat of paint when removed revealed another black coat of paint and finally a gunmetal layer of paint.
The hard part about getting the paint off was really getting it out of the tight corners and I spent most of a day with a set of small needle files picking paint out.
Finally I was ready to paint and ironically I used a filler primer to smooth out the finish of the plastic. I was so pleased with the results, I then turned my attention to the actual wire mesh of the grill itself. As you can also see below the 'S' logo was also worked on pretty heavily. It isn't perfect where the previous owner was an idiot. However it passes my high standards!
The logo was also stripped back and painted (Tamiya Gold)
This is of an all in one design, consisting of a frame, with mesh attached. As the top of the frame actually is on show when the bonnet is closed, it was pretty important to keep this. The wire mesh is made of steel and is quite strong, also being (for mesh) quite large. I decided that I could use some Ripspeed Stretched competition mesh at £24 it wouldn't break the bank etc. This is of Aluminium construction, so rust will not be an issue. It is also quite thin, so cutting it to size would be easy.

With the old grill I chopped out the old mesh with some tin snips. The mesh is actually spot welded to its top frame making this a one way only deal, so it was just a bit scary. I then just counted up the 'holes' in the mesh and cut out a long strip of mesh. I did think about being scientific about cutting the angled ends etc. But in the end I simply held my strip along side the grill and 'chopped away' with a steady hand. Okay so the first attempt was crap! However the second was spot on and happily you get quite a bit of mesh to play with.
I did leave some of the old mesh (where it was spot welded) in the top of the frame, straightened it out and then after fitting the new mesh, bent this back to hold the new mesh in place. I secured the lower part of the mesh in place with body kit glue (just a bit!).

Finished product!
In some strange way cutting the mesh was an enjoyable task, each length requiring two snips per 'mesh hole'.

There's a fair bit more I have been working at and I will be updating as I catch up!

Thursday, 20 October 2011

Slam Panel Part 3 - The Revenge!

Well no, it did not have a revenge on me, I think I have possibly seen too many Jaws films. Although saying that Ms Skyline can sink her teeth into my knuckles now and again!

Continued work on the slam panel today. Flatted back the nice new shiney paint with 1200 grit, even though it wasn't the recommended 24 hours since spraying it, I decided that this was more of a guideline rather than a hard and fast rule... I can be patient... Okay no I wasn't!

It did make me slightly nervous to flatten all of my beautiful black gloss, but hey ho, in for a penny and all that. So after the regulation two minutes shaking I applied two coats of clear laquer leaving 15 minutes between coats.

The finish (for me) is lovely... Although it's very black compared to it's surroundings, this will be fine when all the bright work is replaced.
Finished Slam Panel

I also worked on a couple of the nasty galvanised brackets and sprayed them with a special plastic finish paint. This is textured and dries a matt black. I used this as to get a good gloss finish is a pain, I also thought it would be a good contrast with the (now) high gloss finish.

Plastic Effect Bracket

Whilst on the subject of bright work, I have been experimenting with some 1mm thick rubber and plan to mount this under the fittings of non important parts to save my nice new finish from excessive marking.

Tuesday, 18 October 2011

Slam Panel Part two..

Painting... It drives me nuts! Really!

Okay rant over.. Mini rant that it was. Smoothed off the prime coat this evening and gave a generous blast of black KH1 Kuro Black. Reasonably pleased with the results there are a few 'pin holes' where there is probably contaminants on the surface, but not enough to make me want to sand it all off!

Tomorrow will be the brown trousers. I will give the paint a light sand with 1200 grit to Matt it up and then apply some clear lacquer. This is the bit that is easiest for me to mess up as it's hard to know where to stop with the lacquer!

Here's the work so far... Just looks like a lot of black to me! It's there, honest!


What else did I achieve tonight? Well I have had delivery of a couple of black silicone coupler pipes. I must say, I like, I like a lot! I was thinking perhaps to replace a few more whilst everything is out of the car. However it is a pain to order sizes or for that matter measure sizes, especially as all the pipes are off the car. The only other thing to foil my plan for all couplers to be replaced is the fact that one coupler is buried under all the brown paper shown in the picture...

One other thing I may conduct an experiment with is braided hose. Well, self braided hose to be exact. You can buy braiding to cover existing hoses, it looks a bit of a Devil to do though, in fact the more I think about it the less I want to do it. Will put on my investigating hat!

Painting Heat Shield and Slam Panel

So I have dived straight into work on the final touches for Ms Skyline. After detaching all the pipework I removed the heat sheild from the exhaust manifold as this was letting the side down with it's unattractive looks. I have been warned about painting this as the paint can 'crack off' and would leave it in a worse state than it started. Although I beleive that this would have been if the part was painted in 'normal' acrylics, besides the heat sheild is already painted in silver, so what the hell. I naturally went for a rather fetching shade of black (what else!) High Temperature paint. I can't see me having problems with this although time will tell! I also replaced the three bolts along the visible edge on the top of the sheild with Stainless items. 

If you look to the back of the picture by the turbo, you can see the lovely stainless HKS heatshield plate of the 2835 Pro. The temptation is to infill the backing to the logo in black, although I must resist! 


I have also started work on the 'slam panel' at the front of the car. I know to do it 100% proper I could have removed the fan and headlights. Naturally I have gone for the easy option here! Sorry to all purists out in the world!


No, I'm not going for a fetching shade of grey! This is just the prime coat, the finish will be just plain boring black, the same as the car. Naturally I want to get this out of the way as quickly as possible, with as little mess and fuss as I can get away with.

Monday, 17 October 2011

A Win of sorts..

Well Ms Skyline is back, alas not without a healthy dose of drama! What should have been a straight forward job soon developed into a pain in the butt. I dropped the car into the garage on Saturday morning, the plan being that the work would be done and the car on the dyno by Friday. Wednesday and the first problem reared its ugly head in the shape of a cracked exhaust manifold, this was a real problem as where the hell could a new one be sourced. As luck would have it the garage knew of a used item that could be purchased for £50 locally. Result then and drama avoided. Oh that it were, the replacement manifold was warped and would not fit. Giving the garage it's dues they managed to source another from JDM garage, these are probably the most expensive and unreliable source of parts in the UK. True to form they wanted £86 for the part, although I was desperate so would have probably said yes to anything at that point. Giving JDM Garage their due's they did come through and had the part at the garage next day. Although I would still suspect being 'the man in the street' and not 'the garage'. I would have had a slightly different experience.

So with new 'old' manifold, turbo and camshafts fitted the car went to the tuner...

Naturally this didn't go well either and a decent tick over could not be achieved. To cut the story short, the garage had fitted a R34 camshaft to my R33 (approx 1.5mm extra lift).

Now I can accept a mistake, although everyone seemed to point at everyone else. The garage were not happy and I got a distinct vibe that they were upset at having to do the job again. Personally I can't see how I would have been at fault here, as for once, all I did was pay the money, leaving sourcing of parts to them! The garage said that the wrong camshaft was in the right box. Well it could happen...

The correct camshaft was promised for the start of the week. I heard nothing, nothing and nothing. I asked when the car would be going in and was told maybe Thursday. happily this happened and the car did its thing. I took Friday off work to collect her.

I will come back to the tune etc. in a different post.

The car was unhappy cosmetically under the hood. For some bizarre reason I had beautiful bright blue pipework! What the worlds obsession with blue silicone is I dunno, but it has to go! Where the heat shield fits there are two new bolts and the slam panel had been drilled badly to fit these (can only assume the original bolts were lost). There were plenty of scratches on the slam panel too, the bracket to hold the air filter in place was loose, the Strut brace had been tightened by the bionic man, cracking the powder coating both sides and the new pipework for the turbo was looking a bit tired.

So it's all action again in another lurch towards the finish line. I have prepped the slam panel for painting, removed, polished the pipework, removed the strut brace pending painting and have some silicone black pipes and clamps on order.

Have yet to decide anything, I may send the pipework to chrome, if I do that then I may as well do the strut brace at the same time and get the end's re-powder coated. The silicone is on it's way, although I really need to finished the slam panel. The car's tax is due although possibly I will put this off a month and just forget I own the car a bit!

Think of this as an interim post.. whilst I work out what to do next!